Page 7 of 10
Posted: Sun Jun 10, 2012 10:04 pm
by BIGDADDY1969
Thanks AZrider and Mikel ... Fnally got a chance to download the file AZ had from Mikel .. Its awesome!!!!! Nah if i can get Lew to turn off torquemanagement .... 20% reductn aint enuff!!!!!!! But the tune is awesome guys.....
Posted: Mon Jun 11, 2012 2:35 am
by thilowvg
Oldsaltydog wrote:Go into adjustable parameters firm or hard shift tune shift
It will show
Wot parameters and part throttle parameters
Firmer willbe negetaive towards leftsideof tool
Softer is positive towards right side of tool when changing settings I always reset all
Parameters
This is not available to me on my 07 escalade 6.2L. I am not clear on how you are changing shift pressure etc. I have the option of firm shift or hard shift but it is only adjustable in terms of what RPM it shifts at. What gives?
What is optial RPM for gear changes (especially lower RPM), lower or higher?
Posted: Mon Jun 11, 2012 8:54 am
by 2500hdandk20
I'd like to try it to Mikel!
Posted: Mon Jun 11, 2012 12:56 pm
by twday87
I am assuming he is not sending it out anymore because the update is supposedly available sometime this week for everyone. I asked a few pages back but haven't seen him reply to anyone since. If he is i still want it
Posted: Mon Jun 11, 2012 1:02 pm
by AZ_Rider
Hey Mikel, when is the update for the TCM support going to be available for the automatic download? I received the file you sent but it doesn't look like my Calid is supported.
Posted: Mon Jun 11, 2012 3:00 pm
by mikel
Here goes, anyone who would like to use it, just be sure you are updated to 1r02a first, then drag/drop this to the inTune drive, let the tool reboot, then go to the vehicle and tune away.
Enjoy!
edit:
latest update here (added a few that were missing)
Posted: Mon Jun 11, 2012 3:04 pm
by mikel
grucela wrote:Mike,
Is the TCM support also for the 06 1500 GMC?
they dont have a TCM, trans support for those vehicles has been there since they were added.
Thanks
Posted: Mon Jun 11, 2012 9:11 pm
by BIGDADDY1969
I have the 1t01fe file .. What Does the 1t01ff have thats different?
Posted: Mon Jun 11, 2012 9:36 pm
by Oldsaltydog
Do we need to update again or is the 1t01ff file just Calid updates or do we need to update to this?
Posted: Mon Jun 11, 2012 11:01 pm
by AZ_Rider
I just tried this one, and my Calid is still not supported.
Posted: Mon Jun 11, 2012 11:27 pm
by BIGDADDY1969
Hope u get urs sorted out AZ .. That file i picked up from u with the f-e as last two characters works on my 08 but i have 4speed auto if that makes a diff i dunno.. Its awesome im gunna tinker lil more tomorrow afta i get data log for Lew n get updated from him im see where its settled in at
Posted: Tue Jun 12, 2012 12:17 am
by rdss
I can't wait to get home and try this out. Hopefully all the transmission CalId's have been straightened out by then.
Posted: Tue Jun 12, 2012 8:18 am
by twday87
Im curious as to what everyone else is running with their TCM. I used firm shift mode and set everything to 3 (on the firm side).. Seems to be a nice shift but what do yall think?
Posted: Tue Jun 12, 2012 9:32 am
by mikel
AZ_Rider wrote:I just tried this one, and my Calid is still not supported.
you must have an old calid on your TCM.
We'll have to wait till we can get the tool to read the unsupported calid out, or you could take it to a dealership and have the TCM updated and it will be supported
Posted: Tue Jun 12, 2012 10:31 am
by AZ_Rider
How long will that take to get that part of the tool to read the unsupported calid out?