Page 1 of 1
New Update Needed U7164
Posted: Thu Nov 13, 2008 4:13 pm
by bf6086
Installed the new update dated 11/12/08 on 2-U7164 both trucks got
an update from Ford on 11/11 this now creates a new error.
both programmers will not load and give you a message of
===cant program without dynamic cuts ====let me know whats
next. Thanks 2-08 F350 6.4
RE: New Update Needed U7164
Posted: Thu Nov 13, 2008 4:37 pm
by mikel
Just to be sure, this is with the 9r05 revision?
This error occurs while trying to update the Predator correct, not when trying to tune the truck?
Update Info
Posted: Thu Nov 13, 2008 5:01 pm
by bf6086
Mike; The programmers took the latest 9r05 updates with no issues.
this is during tuneing the trucks. This is a fresh Ford update that was
installed in these trucks it actully came out tuesday of this week.
RE: Update Info
Posted: Thu Nov 13, 2008 5:30 pm
by mikel
Hmmm.
I will look into this.
If possible, can you go to options/troubleshooting/showcalid and tell me what calibrations are listed in the truck?
Thanks
Mike
RE: Update Info
Posted: Thu Nov 13, 2008 8:48 pm
by racing99
Hi i tryed downloading with my new tuner,Predator- u7164, for my 08 ford diesel, it said i could not proceed, wrong calid# o, then it game some numbers unit#1 8c3a-14c204-pd unit#2 8c3a-143337-ca what should i do next, ive tryed downloading the new update 9r05 but it says error on my computer?
Re: RE: Update Info
Posted: Fri Nov 14, 2008 9:40 am
by sohfast94
racing99 wrote:Hi i tryed downloading with my new tuner,Predator- u7164, for my 08 ford diesel, it said i could not proceed, wrong calid# o, then it game some numbers unit#1 8c3a-14c204-pd unit#2 8c3a-143337-ca what should i do next, ive tryed downloading the new update 9r05 but it says error on my computer?
What does it say exactly when it gives you an error on your computer?
Re: New Update Needed U7164
Posted: Fri Nov 14, 2008 9:40 am
by sohfast94
bf6086 wrote:Installed the new update dated 11/12/08 on 2-U7164 both trucks got
an update from Ford on 11/11 this now creates a new error.
both programmers will not load and give you a message of
===cant program without dynamic cuts ====let me know whats
next. Thanks 2-08 F350 6.4
I need your calids so I can get this fixed ASAP...
install error u7164 v.9r05
Posted: Fri Nov 14, 2008 10:55 am
by ytterp
Predator part no: U7164
Predator Revision: v.9r05
Vehicle Year: 2008
Vehicle Make: Ford
Vehicle Model: F250/Diesel
When trying to install tune I get a message -
"Can't install performance tune without dynamic cut"
My Calibration Id:
Unit 1: 8U7A-14C204-AG
Unit 2: 8C3A-14C337-CA
Help! I called your support desk and they suggested that I post the problem on this forum.
RE: install error u7164 v.9r05
Posted: Fri Nov 14, 2008 11:17 am
by sohfast94
yup. Don't have the PCM... Will add on Monday.
U7164 INFO
Posted: Tue Nov 18, 2008 9:40 am
by bf6086
Mike I had the same info from the tuner
8U7A14C204AG UNIT1
8C3AQ14C337CA UNIT 2
Thanks[/b]
RE: U7164 INFO
Posted: Tue Nov 18, 2008 10:22 am
by sohfast94
The AG calibration has not been released by Ford as of yet I'm doing my best to get it this week.
RE: U7164 INFO
Posted: Tue Nov 25, 2008 12:35 pm
by ytterp
Any word from Ford on that AG calibration? I can't even restore the original backup without getting the same "dynamic cut" message.
RE: U7164 INFO
Posted: Tue Nov 25, 2008 7:54 pm
by sohfast94
It's not available from Ford currently
RE: U7164 INFO
Posted: Sun Dec 14, 2008 1:56 pm
by ytterp
Still looking for that AG Calibration from Ford, anything yet?
RE: U7164 INFO
Posted: Mon Dec 15, 2008 10:09 am
by sohfast94
Finally got it and making a new crom now.