Predator 2005 6.0 ==u7165? and rolled back pcm ford6.0

[ssredrino]

ok i have a bubble!!! i hope i can get some help

i have a 2004 f250 4x4 6.0 i have restored the pcm and the ficm back to the original programming when it came off the factory floor and thank god lol i have my truck back

but in the mean time i have updated my preditor 2005 6.0 i bought brand new from k&s in wausa wis and now it has the latest u7165_pcm_6_0-9r15.crom and i have tried 9r13 and 9r14 and both are not the same as when i bought my preditor

i would really like to have my preditor rolled back to the way it was when it was sold to me, i am extremly unhappy with the updates and it makes my truck run like horse dukey either that or DiabloSport should buy it back and please do not tell me that it is not possable.

ford told me the pcm could not be rolled back either but it is
i think it is crapy that we all had to update because of ford writing programs to mask problems that would be covered under warrenty


AMZ2AL09
TQBD1N6
VXBC1NZ
are my trucks programs

[mikel]

we had no choice but to update the tools to keep up with Fords flashes, how would you propose we get around that?
Just tell people who got updated 'too bad'?

Please load a tune then export the backup and last tune written file from the tool, and post them here, and we'll check it out.

[ssredrino]

yep i understand
and sorry for sounding rash

but can you please just let me put u7165_pcm_6_0-8r10_for_power_6_0 or power_6_0-7r84_H512 in my u7165 2003-2006 ford serial 155852

and what ever my 2005 6.0 preditor came with new early in jan/05
this is the original i bought new and dam i loved it then like all others the stealership reprogrammed my truck and finaly i was forced to update my 2005 6.0 preditor wang-wow and then i found bill and he set my truck back to the original programs as if it came from the factory now my truck runs fine and nice and quite again but the preditor does not make it run right now to be honest i have run the preditor on my truck since it was brand new with 200 miles on it it now has 97000 on it
i used to pull 22-24 miles to the gallon with her and power to burn and out run new 05 corvettes
now i get 13-16 and chevetts can take me light to light
my truck will never be at the dealer for service again ever

i just bought the u7165 off from ebay from a guy in canada and had it shipped he said he never updated it but it got here updated to u7165_pcm_6_0-9r13 lol now i have two with the pcm boot 4

here are your two files Mikel
thanks
ssredrino

[ssredrino]

yep i understand
and sorry for sounding rash

but can you please just let me put u7165_pcm_6_0-8r10_for_power_6_0 in my u7165 2003-2006 serial 155852 i bought this unit from a guy in canada who said he never updated it but it came with u7165_pcm_6_0-9r13
now i have 2 preditors with the same pcm bootloader on them

and what ever my 2005 6.0 preditor came with new early in 05 i bought this and installed it when my truck had 200 miles on it now it has 97000 on it but the preditor does not make it run like it did, and yes i too was forced to update my preditor because of ford also. i used to pull 22-24 miles to the gallon and out run new 2005 corvettes

now i pull 13-16 and chevettes beat me light to light

thanks mikel
ssredrino

[ssredrino]

sorry forum said there was an error and it would not show me the post so i reposted

[ssredrino]

u7165_pcm_6_0-9r15 makes my truck have an idle surge with the pilot injection egr delete, 4 inch cat back magnaflow muffler fresh fuel filters all new sensors, new water pump- fan clutch, oill cooler, cleaned turbo.

[Buck02]

I emailed 2 tunes for you.

[Fedz]

Hello, how did you get your 6.0 rolled back to the original Ford tune? I have the same issue, as a shop reflashed my PCM without permission. Any guidance is appreciated.

[ssredrino]

Bill at php power hungry performance rolled back my pcm and tcm upgraded my ficm