Page 1 of 1
INTUNE HELP - 2007 SRT8 Jeep
Posted: Tue Jan 24, 2012 7:26 am
by GonzozSRT8
Hoping you could help me out. Just got my Intune. Updated via the web.
plugged it in my 2007 Jeep SRT8, asked to update for Jeep. Brought it
back in and did that on the PC. Plugged it back in the Jeep.
Message comes up "Determining vehicle info, please turn ignition to "on" pos'n.
Done. Then new message:
"Calibration update is ready to install. Install now?"
Pressing yes get me " Wiriting Tune: 1%"
then "an error occurred while installing calibration update"
"Continue"
clicking continue gets me:
"Itune is in recovery mode: continue?"
yes/no
Yes replays this scenario, no gets me :
"No ECU's found. Check ignition Key"
with a green checkmark after. which just keeps coming back
after I press it.
Hoping you can help.
Kevin
RE: INTUNE HELP - 2007 SRT8 Jeep
Posted: Tue Jan 24, 2012 10:31 am
by JonDiablosport
Lets try to get that unit back to a brand new state will require a few codes etc so if please give us a call and we will see if we can get you through this or take note to fix the issue.
RE: INTUNE HELP - 2007 SRT8 Jeep
Posted: Tue Jan 24, 2012 10:44 am
by mikel
can you post or email the info.xml file here from the intune drive?
does the vehicle run currently.
Thanks
RE: INTUNE HELP - 2007 SRT8 Jeep
Posted: Tue Jan 24, 2012 12:05 pm
by GonzozSRT8
vehicle is running fine. check engine light is on though
here's the info.xml
<?xml version="1.0"?>
-<tool_info>
<main svn="3753" sw_rev="1r01d" full_version="InTune-1r01d 01/11/2012 11:05:00 AM"/>
<registration status="1" sn="CIAU070-1"/>
<restore bc="0" vin="1J8HR78307C579394" id="0"/>
<db pid="1r01a" tune="1r01b" mfr="GM"/>
<db pid="1r01a" tune="1r01a" mfr="DCX"/>
<db mfr="FORD"/> <system_db vin="1r01a" info="1r01a" dtc="1r01a"/>
<license tuned="0" avail="1"/>
</tool_info>
RE: INTUNE HELP - 2007 SRT8 Jeep
Posted: Tue Jan 24, 2012 12:11 pm
by mikel
OK, looking into it.
RE: INTUNE HELP - 2007 SRT8 Jeep
Posted: Tue Jan 24, 2012 12:21 pm
by GonzozSRT8
thanks
RE: INTUNE HELP - 2007 SRT8 Jeep
Posted: Tue Jan 24, 2012 3:40 pm
by GonzozSRT8
Any chance this has to do with the fact it's a Canadian Jeep?
RE: INTUNE HELP - 2007 SRT8 Jeep
Posted: Tue Jan 24, 2012 4:01 pm
by mikel
shouldn't, no.
RE: INTUNE HELP - 2007 SRT8 Jeep
Posted: Wed Jan 25, 2012 7:20 am
by GonzozSRT8
Any luck?
RE: INTUNE HELP - 2007 SRT8 Jeep
Posted: Wed Jan 25, 2012 10:30 am
by mikel
Yes, we have a fix, please give us a call with the tool powered up at your PC.
RE: INTUNE HELP - 2007 SRT8 Jeep
Posted: Wed Jan 25, 2012 12:02 pm
by GonzozSRT8
ok, will call in about 50 minutes when my lunch starts
RE: INTUNE HELP - 2007 SRT8 Jeep
Posted: Wed Jan 25, 2012 1:34 pm
by GonzozSRT8
Called, was on hold for 5 minutes. Assuming you were either busy or on lunch.
Will try again at around 2:45.
Thanks
RE: INTUNE HELP - 2007 SRT8 Jeep
Posted: Thu Jan 26, 2012 9:40 am
by GonzozSRT8
Awesome support to get this sorted out. Sorry I didn't get the name of who helped yesterday.
Thanks again.
Kevin
RE: INTUNE HELP - 2007 SRT8 Jeep
Posted: Thu Jan 26, 2012 10:29 am
by mikel
Again, glad we could help, and thank you for being patient!
RE: INTUNE HELP - 2007 SRT8 Jeep
Posted: Thu Jan 26, 2012 2:06 pm
by Vas@Diablosport
You spoke with me on the phone. And as mike said, thanks for your patience with us while we sort this out.